we soon saw the establishment of the plates ....
- "You're right we'll go over the details !"
by "above" you speak of chassis
- "Yes, of course! "
ah! ok because there is more you that we see




- "I don't know if the last time you noticed a party had not suffered the onslaught of the grinder "
yes the top of the chassis, why?
- "It's fixed "




ops
- "The chassis is significantly lighter now "




this is clear! we are only the amounts?
- "Now, we see the introduction of aluminum plates "
ok! and we start by....
- "By the back of the chassis "




them took a good slap
- "It is true that we have not even the framework ... just those two amounts "
you put the plate in place
- "Yes and is positioned behind the amounts "
all fixed by ....
- "Screw and bolt "
simpler than rivets
- "Especially if you need to disassemble and reassemble the chassis "




ops you're still with the rear ....
- "No! There is the front "
okay ...




and the plate?
- "It takes place within the amounts "




simple
- "yes and ....no "
ah?
- "We had to make some cuts to these small openings "
okay! and we can't cork them?
- "Well! no, the holes used to attach the fairing to the chassis "




next...
- "the top "
he already has a specific section
- "Yes rectangular ...."




and now you are with....
- "plate "
plate positioned inside
- "Exactly "




- "There were also a few openings ..."
that correspond to passages clips fairing
- "Small rectangles, small round .... "




it's good to put the plates, but now we must re-assemble everything ops
- "Quite well and see if it still coincides "




the front part
- "the rear part "




the top
- "no not yet "
ah!
- "and yes ... we will look at another plate "
large plate




I already told you that you were little
- " "
you seem lost in this immensity
- " "




- "bref! .... this is not just an aluminum plate"
ops
- "It is based on a thick acrylic plate "
what for ....
- "It will be seen later "




it used to ....
- "This is the motherboard tray "




- "On the side of the backstage "
a real wall ops
- "The base is in place we will pass the details now "




you want to talk about interior design
- "foundations of the case are in place "
thinking about the positioning of the components is fixed
- "right "
360 radiator at the bottom of the case
- "Push / pull"




BTX motherboard position
- "Yes and here we must have a back plate ops "
it's true that the original back failed to get that plate ...
- "We went to find an old box ...."
This thrown
- " "




we'll see how high the motherboard is positioned
- "Small current debate "




we leave on ....
- "A small box "
filled ....
- "Steel of all kinds "

hello
- "yep! "
not hello....
- "It's like, no "
okay ... what we present today?
- "We will focus on the rear of the chassis "
and as we have seen, we went to retrieve a backplate




- "We could make one "
euh ....
- "But as we had this copy on hand "
we let's say it like that
- "For positioning the plate on the rear part of the chassis ...."
we must first position the motherboard tray
- "Here we go "




ok! we mark the backplate on the aluminum
- "2-3 small holes to maintain "




- "And features cutouts are marked on the aluminum plate to access the rear of the motherboard"
on this condition, we will be difficult to connect the devices




- "A bit of a saw for cutting "
a little bit of lime to catch the right line




what are you doing with this profile aluminum?
- "To hide some holes "
one that is your left foot
- "Especially "




you said a few holes
- " I take this opportunity to fill two expansion ports "
I see that !!!




ops ops ops what you want in your hand ???
- "A cut "
fine cut
- "Smooth "




- "lace, I would say "




and cutting is for?
- "Art Deco "
it's true that we have not given the theme of the mod
- "Oh, they'll figure it out for themselves "




you want to be framed
- "No need to frame to put me in value "
ops




- "tell me cuc', you can zoom in on me "
... how many times will I say that you are not you ....
- "No it is not for me "
euh ....
- "Though ... but it's also to show that we have different milling holes "




after the framework is a circle !!!!
- "History of breaking the style "
I hope at least that is useful
- "Like putting me in value "
but you just said .... I give up ....




- "no more humor cuc' "
...
- "okay! it is for this "




- "But before...."
we will prepare this item
- "To make it in adequacy with the style "




next?
- "we went back to work "
A +

Hello everyone
- "Hello everyone "
today ....
- "We will move forward in the presentation of the work done "
for sure! otherwise he will think we are at a standstill ....
- "A ride on the bottom of the case "
was somewhat removed from the plastic to have something flat




- "we mask "
our work ???
- " "




- "No! this is a trick to locate the fans ...."
develops Xray! develops!
- "One hand on the implementation of the 360 radiator on the bottom of the case "
and we saw that it fits nickel in the bottom's fairing
- "We put in place the fans on the radiator and I put a little bit of pencil on screws "




- "And ...."
and ???
- "And before the felt dry, I positioned the radiator and I press ...."
you press?
- "We press to realize the marking of the position of the screws "
cool!




we have reference of the screw holes but not for the fans themselves ....
- "A landmark begets another "
ok! we find the center of the circle and presto!
- "Hop! and is cut "
given the configuration of the fairing, it was necessary to use the drill and lime
- "Rapidly performed by the plastic work "




- "setting in situation fans "




- "We're going to see the establishment of a filter element ..."
otherwise hello dust
- "Should not be the case turns into a vacuum "




and there?
- "A small cut on aluminum plate "
euh .... it is clear to cut .... it is rather the function of the thing I want t know....




- "we positioned the radiator with fans on push-pull "
and plate ???




- "we put in place to cover the base of the cutouts of the chassis "
a hidden misery ...
- " "




next?
- "soon "

and we are back
- "We do not hang today "

- "After the establishment of the radiator, we will not leave it all well "
no! of course!
- "so we take a cardboard "
a cardboard ????




- "As we do not handle apps like Sketchup .... nothing like a cardboard cut-outs to preview "





- "Now we know the size of the aluminum plate cut out "
us cut out!




- "We have already seen for locating the position of the fans ..."
and therefore for cutting openings ...
- ".... On the aluminum plate "




but the plate is flat!
- "It's better to make the cut "
it is how to make the shroud?
- "The bender that goes well used :whistling: ...."




another cutting ???
- "Yes "
ah !!!
- "On an acrylic plate "
and the blue stuff?
- "to facilitate cutting "




-"we reduce the size of the plate "




- "And adjusted as close openings "
???? ops ops




this is for training?
- "Not really "
why then ???
- "We will see this later , first we will look at this cardboard "
another one?
- "yes but package "




and there is?
- "Wrapping mod "

- "Tadaaaa !!! "




leather!
- "100% "
several aspect of brown
- "A bit of nuance, indeed we return to our fairing "




- "A neoprene adhesive layer on the plate and on the leather "
fine layer
- "As much as possible if we want something flat "
the best is the bomb glue...
- "But we want a little relief, so the "raclette" is used "
I love raclette (french joke)
- "Okay ...."




- "I skin folds on the other side of the fairing "
with a cut star for openings fans
- "And that's where I put up the acrylic sheet"
to keep the folds
- "Among other things but that is not its main function "




the wire puts us on track
- "Then plug "
go!




I turned off?
- "yes! to better reflect the light diffusion "




but tell me Xray!
- "Yes ...."
you have not made a cut too ....
- "Too much?"
what you have on the back
- " what do you think about?"




- "Still dreaming of a leather jacket "
the cut is poor




- "Bah! I think it suits me "
nothing dress you Xray! nothing dress you
- "There's nothing to say "
more with the red shorts ....
- "Class "




Returning on the mod ....
- "You're right "
the wooden board with the name of our sponsor that is a cut?
- "not exactly! you missed one detail "
which?
- "The brass rod at my feet "




and then ....
- "The board will be my model actually "
if you say so ....
- "And you'll help me twist the stem in every way "
okay
......
a good time is going
......
.....
- "And here is the result "




cool but what have you in your hand? a ring?
- "A ring?"
then a bracelet ....
- "Bracelet ????"
after the necklace, I expect everything with you
- "No! you're not there at all ...."




- "it is the point of be quiet "
okayyyy




how do you hold this?
- "With a brass wire and discreet hole through of the fairing to pass the wire "

- "Soon "

no time to lose! we continue
- "It's an avalanche of update "
This is what can be
- "At least that is almost finished "
and there it is ....
- "from the top of the case "
which was plugged the holes with mastic




- "sanded and sanded and sanded again ....."
masticated again ....
- "I still sanding then?"
must you need
- "So we plugged the holes of the front panel "




- "holes for superior ventilation of the case "
no more upper ventilation !!!
- "don't worry "




- "You know we love reseal the holes ...."




- "To make others "




superior ventilation is again up
- "We will not let these holes as well "
nothing like a grid
- "Custom "
the cutting plotter is useful to realize the cutting pattern
- "It simplifies the task "




a good small time on a scroll saw ....
- "We should not miss "
Yes! take your time is obligatory




- "A small setting in situation "




it is fixed with ....
- "Screw and bolt brass said one-eyed "




we ended up with the top of the case?
- "not yet "
ok and we go on ....
- "the fan controler that goes well "
special dedicated to the theme of the mod




- "We undressed"
4 small holes are made
- "The difficulty is the alignment of these openings ..."
tip top




- "We need to see or not if we make holes for the LEDs Rheobus ..."




- "The radiator 360 takes position at the bottom of case"
we saw it ....
- "then the supply takes place elsewhere ...."
then of course! :p
- "And therefore no more access to the mains connection ...."
ouch! not false ....
- "So we invest in a remote "

- "special dedicace to Gdesmo "




- "And positioned on top of the case "
ah! Why?
- "Because the power given to the top also at least its back"




it's all good now
- "not yet "
ops
- "There is a hole that is not plugged .... "
ops
- "The start button "




and do not let him as ....
- "Oh no! "
a small cut on acrylic plate shaped gear ....
- "Oh yes! "




but the button is square !!!!
- "That's why we made a cut to our internal gear "





this time it's over?
- "Until next time "

good morning and good weekend
- "Hello here we have sunny day "
... otherwise Xray that we present today?
- "motherboard "
euh ... ok .... but we did not already presented ...?
- "then yes ... but I wanted to once again show "
ah ....
- "Yes one last time before ...."
before .... ops
- "What is the purpose of today's post "




- "And at first, we take care of sinks "
both are removed




the bottle !!! is for ????
- "sinks "
ah! and?
- "we will clean things up a bit in depth with this bottle of lye "
laundry ???
- "a recommendation from a friend "
you manage?
- "you're worried about "
ok ...
- "you just keep an eye ... if not you have no anodizing and aluminum material too ..."
ops ops ops




- "sink of mosfets is the first to go to pot "
the red parts are actually doing "trempouille"?
- "no ... I actually taking them out ..."

- "No need "
downright ...
- "Yes "





- "I keep removing the light part ..."
what a surprise!
- "Oh !!!!"
you who usually like light effects
- "Yes, but not here "
but! but !!!! what are you doing ????
- "Small pieces "




bah why ???
- "better to have my new pieces "




- "3 mm aluminum plate "
saw cut a scroll
- "It heats! it heats!!! "




- "and here my little cut and sanded pieces "
you did not like the scratch mommy dragon ...
- "there is a bit of that but mostly it will be fine with the mod "




- "look, if it's not good way "
is left as?
- "for now we will now move to another one"




sink of chipset
- "exact "
we take away the small plate that is in contact with the chipset of the motherboard
- "and it's ready to hang her bath "




- "better than decap oven "

- "there is the imprint of the badge ...."

- "we will take care later ...."




ok! so you take now this acrylic plate
- "quite "
and that is ....
- "draw lines "
super ....




- "Yes, but not only ...."
I see that as cutting
- "following draw lines "




- "and we end up sanding plate "
not really transparent ...
- "not matter "




I think it all coincides with the elements of the motherboard
- "upwind hair "
big hair then
- " "




returning to our sink
- "I stuck it a little filler to smooth the surface "




- "then it's leather operation"
with double-sided tape
- "I would rather not try the glue on this acrylic plate "
it is better safe side
- "especially after all the cuts ..."




but tell me!
- "I'm listening ...."
speaking of cuts
- "Ouiii ...."
thou hast taken away!
- "Ah you think!"
more than believe! I am sure
- "Ah, if you say so ...."




now what?
- "we take care of the rear modules on the motherboard "
bah! there is integrated fairing at this level
- "Yes! nickel for the top view but on a rear view ...."
it's not false
- "blow masking operation ..."
followed by painting operations




tell me!
- "I'm listening again ...
we must not forget the module wifi and bluetooth combo
- "It dries "




- "A little black on the plastics "
ops not easy with all those blue and red ....
- "we want to apply color match but it does not help us spot ..."




ah well better once painted
- "I did not intend to leave them raw aluminum "




wow!!!
- "It throws "
all those little cogs ... !!!
- "since the motherboard disappears under its fairing "
and then it coordinates well with the style of mod
- "A clockwork dragon "
it gives time ???
- "Still not "



what this?
- "another ... no... four other things that will take place on the motherboard "
at least the shell
- "Red "
which means they will take a bath also
- "once the stickers removed "




then it's paint
- "Which is not bad as it is the black PCB"
clear




I do not want to be flip joy ... but you do not have a defect in the paint
- "Ah you saw ...."
I would have a hard time not seeing
- "OK, it is not bad "
not bad ???
- "yeah, I think it's nickel to have this defect it gives a hand hammered copper "
:eek: you know bounce off your misses, you !!!
- "this is what is called fit "
and that's how you shit varnish and finally we get a top tip effect
- " "




have a nice day
- "see you soon "